spacer

Search results for "switches"

Mini pneumatic vacuum switches

Mini pneumatic vacuum switches

These extremely compact vacuum switches give or remove a pneumatic signal, depending on the model, when a certain adjustable level of vacuum is reached.
The pressure differential existing between the set maximum value and that of the signal recovery at rest is not adjustable.
They are particularly suited for controlling vacuum generators and for activating pneumatic valves.
Product codes: 120130 120230

File CAD su TraceParts
3.06  
torna in cima
Micro digital vacuum switches

Micro digital vacuum switches

If accurately calibrated and compensated for temperatures, these small devices are able to give very precise digital signals to the set maximum measuring value.
The switching point, which is within the scale value, can be easily programmed by means of an adjustment screw located on the upper part of the device. A red LED near the screw indicates the digital output signal commutation status. The pressure differential (hysteresis) between the set maximum value and the value of reset of the rest signal is 2% of the set value and cannot be adjusted.
They are composed of a polycarbonate enclosure, which includes the sensor and the electric circuit, and of a coupler or a small aluminium manifold with the vacuum connections.
Item 12 05 10 can also be rotated freely to place the display in the desired position, without having to unscrew it from the vacuum connection. The vacuum connection can be carried out via male or female M5 connectors, while the electrical connection is made via a three-connector cable with which they are equipped. Mini digital vacuum switches are suited for controlling dry air and non-corrosive gasses. They are recommended in all those cases that require a signal when a certain level of vacuum is reached, for safety, for starting a cycle, for checking the cup grip, etc.
Product codes: 120510P 120510N 120511P 120511N

File CAD su TraceParts
torna in cima
Analogue vacuum switch

Analogue vacuum switch

These compact and extremely light switches come enclosed in a sturdy ABS casing; these features allow their installation on the machine and close to the application. If accurately calibrated, these analogue switches provide very precise measurements values.
The adjustment range is from 0 to -1 bar and can be interfaced with external logics via an analogue output from 1 to 5 Volts and a digital PNP output, configurable via Teach-In.
The switching point, as well as the hysteresis from 0 to 100% of the set value, can be easily programmed via push buttons located on the control panel; the two two-colour LEDs on the control panel signal the commutation status and the error code, if any.
These devices can be rotated freely to place the display in the desired position, without having to unscrew them from the vacuum connection.
The vacuum connection is dual threaded: male G 1/8” or female M5. The electrical connection is an M8 4-pin threaded plug and upon request the connection cable is available in PUR, with an axial or radial connector.
These vacuum switches are suited for measuring and controlling dry air and non-corrosive gasses.
They are recommended in all those cases that require a measurement and commutation to be installed on safety or energy-saving devices, on systems for optimising the work cycle time and in circuit level of vacuum adjustment circuits.
Product codes: 120710

File CAD su TraceParts
torna in cima
Digital vacuum and pressure switches

Digital vacuum and pressure switches

These compact and extremely light digital vacuum and pressure switches are enclosed in a sturdy ABS casing. These features allow installation on the machine and close to the application.
These digital switches are accurately calibrated and compensated for temperatures and therefore are able to give very precise measurements values. The detected values are shown on the display, making it unnecessary to use a vacuum gauge. The two LEDs, one red and one green, built-in the control panel, indicate the commutation status of the two digital output signals.
The two commutation outputs are completely independent. The switching points within the scale values, including hysteresis from 0 to 100% of the set value, are easily programmable via the buttons located on the control panel.
Other additional functions can be configured, such as the comparison between two values, NO and NC contacts, choice of the measurement unit, locking the programmed values and functions, display reversal, etc. These devices can be rotated freely to place the display in the desired position, without having to unscrew them from the vacuum connection.
The vacuum or the pressure connections can be carried out via a dual male G 1/8” or female M5 threading. The electrical connection is an M8 4-pin threaded plug and upon request the connection cable is available in PUR, with an axial or radial connector. These switches are suited for measuring and controlling dry air and non-corrosive gas.
They are recommended in all those cases that require a signal when a certain level of vacuum is reached set for safety, for starting a cycle, for checking the cup grip, etc. Moreover, the hysteresis function allows managing the vacuum generator compressed air supply, allowing considerable energy saving.
Product codes: 121010 122511 001220 001221 001222

File CAD su TraceParts
torna in cima
Accessories for analogue and digital vacuum and pressure switches

Accessories for analogue and digital vacuum and pressure switches

Cable with axial connector
Cable with radial connector
Wall-mounting kit
Fixing kit
Product codes: 001220 001221 001222 001230 001231 001232 001240 001241 001242 001243

File CAD su TraceParts
torna in cima
Digital vacuum and pressure switches

Digital vacuum and pressure switches

These compact and extremely light switches come enclosed in a sturdy ABS casing; these features allow their installation on the machine and close to the application.
These digital switches are accurately calibrated and compensated for temperatures and therefore are able to give very precise measurements values. The detected values are shown on the display, making it unnecessary to use a vacuum gauge. The two LEDs, one red and one green, built-in the control panel, indicate the commutation status of the two digital output signals.
The two commutation outputs are completely independent.
The switching points within the scale values, including hysteresis, are easily programmable via the buttons located on the control panel.
Additional functions are also programmable, such as comparison between two values, NO and NC contacts, choice of the unit of measurement, programmed value and function blocking, etc.
The vacuum or the pressure connections can be carried out via a dual connection with female G 1/8” thread, while the electrical connection is carried out through the 4-conductor cable with which they are equipped. These switches are suited for measuring and controlling dry air and non-corrosive gas.
They are recommended in all those cases that require a signal when a certain level of vacuum is reached set for safety, for starting a cycle, for checking the cup grip, etc. Moreover, the hysteresis function allows managing the vacuum generator compressed air supply, allowing considerable energy saving.
Product codes: 122010P 123510P

File CAD su TraceParts
torna in cima
Digital vacuum switches

Digital vacuum switches

Changes the shape of these digital vacuum switches with respect to those previously described, from cylindrical to parallelepiped. However, the container in which they are enclosed remains in ABS and is also especially compact and extremely light to allow for its installation on board automatisms and near use.
These carefully calibrated devices are able to provide very accurate measurement values. The detected values are shown on the display, making it unnecessary to use a vacuum gauge.
The panel includes two LED indicators, one green and one red, which indicate the switching status of the two digital output signals. The switching outputs are completely independent. The switching points within the scale values, including hysteresis from 0 to 100% of the set value, are easily programmable via the buttons located on the control panel.
Other additional functions can be configured, such as the comparisons between values, NO and NC contacts, the choice of the units of measure, the blocking of functions and programmed values, etc.
The vacuum connection can be made by means of a G 1/8” male or M5 female double threading connection.
Electrical connection for item 12 30 10 is push-in with a M8-4 pin threaded jack. A connection cable can be provided in PUR upon request with corresponding axial or radial connector.
Instead, item 12 30 10 A already has an integrated PUR, 2-metre long connection cable. The adjustment range of vacuum switch 12 30 10 is from 0 to -1 bar, with two digital PNP outputs that can be set by means of Teach-in. The adjustment range of item 12 30 10 A, while it is also between 0 and -1 bar, can instead be interfaced with external logics via a 1 to 5 volt analogue output and two digital PNP outputs.
This series of digital vacuum switches is suitable for measuring and control of dry air and non-corrosive gases. These are recommended in all cases where maximum and minimum value signalling is required, set for safety reasons, in order to start a work cycle, to control vacuum cup gripping, and so on. In addition, with the hysteresis function, it is possible to manage the compressed air supply to the vacuum generators, allowing for considerable energy savings.
Product codes: 123010A 123010

File CAD su TraceParts
torna in cima
Digital vacuum and pressure switches with two-colour display

Digital vacuum and pressure switches with two-colour display

These devices are also enclosed within a robust ABS container. They are carefully calibrated and at compensated temperature, ensuring high-precision measurement values. Detected values are viewed on the main two-colour (red and green) display and programmable by the user to set different conditions. Setting values are easily viewable on a secondary display within the command panel. Two luminous indicators pertaining to outlets 1 and 2 indicate the switching status of both digital and the analogue output signals. The switching outputs are completely independent.
The switching points within the scale values, including hysteresis, are easily programmable via the buttons located on the control panel. Additional functions are also programmable, such as comparison between two values, NO and NC contacts, choice of measurement unit, programmed value and function blocking, etc. The connection to the vacuum may be established by means of a male G 1/8" or female M5 double threading connection. It is possible to establish an electric connection by means of a removable, rapid installation data cable, supplied as standard. Digital vacuum and pressure switches are suitable for measuring and controlling dry air and non-corrosive gases. They are recommended in all those cases that require a signal when a certain level of vacuum is reached set for safety, for starting a cycle, for checking the cup grip, etc. Moreover, the hysteresis function allows managing the vacuum generator compressed air supply, allowing considerable energy saving.
Product codes: 124010 124012 124020 001240 001241 001242 001243

File CAD su TraceParts
torna in cima
Multi-function modules with built-in vacuum solenoid valves

Multi-function modules with built-in vacuum solenoid valves

The needs of technical designers in the packaging sector and in the automation sector in general to have more vacuum combined with different functions in the smallest possible space has led us to design and implement this new series of multi-function modules.
Each module has two internal solenoid valves built inside it. Their ducts house the seats for the flow control valves, which can be operated externally by means of special knobs. Various connections made at different points allow for connection of the module to instruments for reading and checking the level of vacuum, such as vacuum gauges, vacuum switches, transducers, etc.
There are three modules currently available:
- Module A: the basic module with two integrated 1”1/2 and 1” solenoid valves, two flow regulators and several additional connections.
- Module B: with two integrated 1/2 "and 1" solenoid valves and two flow regulators. Can be combined with modules A and C.
- Module C: module with two integrated 1/2” solenoid valves, a flow regulator and an additional connection.
Can be combined with module A or B.
The combination of modules A, B and C, feasible using special stainless steel tie-rods, allows for the application of various functions from a single source of vacuum, as well as allowing for the elimination of numerous pipes and fittings, often causing leaks. The multi-function modules are supplied already tested to a guaranteed final level of vacuum of 0.5 mbar and perfectly sealed.
The technical characteristics are those of the pneumatically actuated three-way vacuum solenoid valves:
- Servo-control pressure: 6-7 bar; 4-6 bar for version LP, with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4
- Operating pressure: from 0.5 to 3000 absolute mbar
- Electric coils: fully plastic-coated in synthetic resin, watertight, insulation class F (up to 155°C) as per standard VDE, with 3 mm two-terminal electrical connections for connectors in compliance with EN 175301-803
- Protection degree IP 54; IP 65 with connector inserted.
- Tolerance permitted on the nominal voltage value: ± 10%
- Electrical power of the coils: from 1 to 2 W, depending on the electrical voltage
- Temperature of suctioned fluid: from – 5 to + 60°C
The ideal use of these multi-function modules is on vacuum thermoformers and vacuum thermo-welders, but they are also widely used on packaging and filling machines in the packaging sector and in all those cases where it is necessary to manage the vacuum at different points and times. Upon request, the modules can be customised and implemented with solenoid valves up to 3” gas. Contact our technical department for further information.

File CAD su TraceParts
torna in cima
Horizontal safety pump sets – General description

Horizontal safety pump sets – General description

Safety pump sets have been designed to centralise vacuum in all work environments such as hospitals, laboratories, etc. where vacuum must be guaranteed 24/7.
They are essentially composed of:
- A horizontal welded sheet steel tank with perfect vacuum seal.
- Two rotary vane vacuum pumps to be selected according to the required suctionflow rate and level of vacuum.
- A vacuum gauge for a direct reading of the level of vacuum in the tank.
- Two manual valves for vacuum interception, located between the pumps and the tank and one installed on the tank, for the exclusion or connection of the pump set on a user system.
- A cock for condensation drainage.
- A switchgear enclosed in a special watertight metal casing with switches for automatic or manual pump operation, an alarm device with sound and light signal, alarm-test buttons and hour-counter for counting the hours of actual operation of every single pump.
These safety pump sets normally provide for the operation of one pump with subsequent automatic insertion of the second one for larger consumptions and when, for whatever reason, the plant level of vacuum goes under the preset value.
The automatic timed inverter, located on the switchboard, accurately alternates the pump start-up, so that they are both subject to the same mechanical wear.
The switchboard and remote alarm systems operate when the plant level of vacuum is below the set safety value.

File CAD su TraceParts
7.71  
torna in cima
Vertical safety pump sets – General description

Vertical safety pump sets – General description

Safety pump sets have been designed to centralise vacuum in all work environments such as hospitals, laboratories, etc. where vacuum must be guaranteed 24/7.
They are essentially composed of:
- A vertical welded sheet steel tank with perfect vacuum seal.
- Two rotary vane vacuum pumps to be selected according to the required suctionflow rate and level of vacuum.
- A vacuum gauge for a direct reading of the level of vacuum in the tank.
- Two manual valves for vacuum interception, located between the pumps and the tank and one installed on the tank, for the exclusion or connection of the pump set on a user system.
- A cock for condensation drainage.
- A switchgear enclosed in a special watertight metal casing with switches for automatic or manual pump operation, an alarm device with sound and light signal, alarm-test buttons and hour-counter for counting the hours of actual operation of every single pump.
These safety pump sets normally provide for the operation of one pump with subsequent automatic insertion of the second one for larger consumptions and when, for whatever reason, the plant level of vacuum goes under the preset value.
The automatic timed inverter, located on the switchboard, accurately alternates the pump start-up, so that they are both subject to the same mechanical wear.
The switchboard and remote alarm systems operate when the plant level of vacuum is below the set safety value.

File CAD su TraceParts
7.77  
torna in cima
Switchgear for pump sets with two pumps

Switchgear for pump sets with two pumps

The pump set switchgear is enclosed in a special watertight metal casing and can manage two vacuum pumps, each with a power up to 7.5 KW as well as maintain the level of vacuum in the tank, set with the digital vacuum switch.
It is equipped with two remote control switches with thermal protection, fuses, a transformer for low voltage auxiliary command power supply, a line switch, a changeover switches for the automatic or manual pump operation, an easily-programmable digital vacuum switch suitable for setting and controlling all vacuum functions, two hour-counters for measuring the actual pump operation time and signalling lamps.
Product codes: D2V15095V

File CAD su TraceParts
7.89  
torna in cima
Switchgear for safety pump set with two pumps

Switchgear for safety pump set with two pumps

The pump set switchgear, is enclosed in a special watertight metal casing andautomatically manages two vacuum pumps, each with a power up to 7.5 KW and maintains the level of vacuum in the tank, set with the two easily-programmable digital vacuum switches, suitable for setting and controlling all vacuum functions.
It is equipped with two remote control switches with thermal protection, fuses, a transformer for low voltage auxiliary command power supply, a line switch, a changeover switches for the automatic or manual pump operation, two digital vacuum switches, two hour-counters for measuring the actual pump operation time, an alarm siren with acoustic and lit signalling, a key selector for any necessary exclusion of the siren, test buttons and signalling lamps.
The switchgear is normally provides for the operation of one pump with subsequent automatic insertion of the second one for larger consumptions and when, for whatever reason, the plant level of vacuum goes under the preset value.
The automatic timed inverter precisely alternates priority pump start-up of the services so that they are subjected to equal mechanical wear. The switchboard and remote alarm systems operate when the plant level of vacuum is below the set safety value.
Product codes: DSO30097V

File CAD su TraceParts
7.89  
torna in cima
Switchgear for safety pump sets with three pumps

Switchgear for safety pump sets with three pumps

The pump set switchgear, is enclosed in a special watertight metal casing andautomatically manages three vacuum pumps, each with a power up to 7.5 KW and maintains the level of vacuum in the tank, set with the two easily-programmable digital vacuum switches, suitable for setting and controlling all vacuum functions.
It is equipped with three remote control switches with thermal protection, fuses, a transformer for low voltage auxiliary command power supply, a line switch, a changeover switches for the automatic or manual pump operation, three digital vacuum switches, two hour-counters for measuring the actual pump operation time, an alarm siren with acoustic and lit signalling, a key selector for any necessary exclusion of the siren, test buttons and signalling lamps. The switchgear is normally provides for the operation of one pump with subsequent automatic insertion of the other two for larger consumptions and when, for whatever reason, the plant level of vacuum goes under the preset value.
The automatic timed inverter precisely alternates priority pump start-up of the services so that they are subjected to equal mechanical wear. The switchboard and remote alarm systems operate when the plant level of vacuum is below the set safety value.
Product codes: DSO30098V

File CAD su TraceParts
7.90  
torna in cima
Switchgear for safety pump set with four pumps

Switchgear for safety pump set with four pumps

The safety pump set switchgear is enclosed in a special watertight metal casing and it automatically manages four vacuum pumps, each with a power up to 7.5 KW, and maintains the level of vacuum in the tank, set with the two easily-programmable digital vacuum switches, suitable for setting and controlling all vacuum functions. It is equipped with four remote control switches with thermal protection, fuses, a transformer for low voltage auxiliary command power supply, a line switch, a changeover switches for the automatic or manual pump operation, two digital vacuum switches, four hour-counters for measuring the actual pump operation time, an alarm siren with acoustic and lit signalling, a key selector for any necessary exclusion of the siren, test buttons and signalling lamps.
These switchgears normally provide for the operation of two pumps and the subsequent automatic insertion of the other two for larger consumptions and when, for whatever reason, the plant level of vacuum goes below the preset value.
The automatic timed inverter precisely alternates priority pump start-up of the services so that they are subjected to equal mechanical wear.
The switchboard and remote alarm systems operate when the plant level of vacuum is below the set safety value
Product code: DSV200099V

File CAD su TraceParts
7.90  
torna in cima
Switchgear for single pump

Switchgear for single pump

The need to use the same vacuum pump in various spots in the work environment,such as, for example, a shipyard, has led us to creating this mobile switchgear that allows for polarity reversal in presence of current, as well as for time setting pump operation and the automatic start-up restoration in case of accidental black-out.
The switchgear is enclosed in a special watertight metal casing and it is composed of fuses, remote control switches with thermal protection and a transformer for low voltage auxiliary command power supply. The following are instead installed on the casing lid:
- A line switch with indicator light
- A changeover switch for pump start-up with indicator light
- A changeover switch for polarity reversal
- An emergency button
- A timer for setting the duration of pump operation
- An hour-counter for counting the actual pump operation time
- A malfunction warning light.
This switchgear is supplied in special metal watertight casing and can manage pumps with power up to 7.5 Kw.
Product code: DO10094

File CAD su TraceParts
7.91  
torna in cima
Accessories for single-stage vacuum generators - Pneumatic coaxial shutter valves

Accessories for single-stage vacuum generators - Pneumatic coaxial shutter valves

The function of these solenoid valves is to intercept the compressed air supply to the vacuum generators. Interception through an original coaxial shutter allows the supply of large quantities of air, thus ensuring greater gripping speed of the vacuum cups.
They are composed of an anodised aluminium body with an integrated coaxial shutter, pneumatically operated by a micro solenoid valve with low absorption electric coil, capable of managing operating pressures between 1.5 and 7 bar.
They can be controlled via vacuum switches or simple electrical switches.
Thanks to their compactness, it is also possible to install them directly on the vacuum generators, thus eliminating unnecessary pipes and negative volumes.
Product codes: VPE00NCV24CC VPE00NOV24CC VPE01NCV24CC VPE01NOV24CC VPE02NCV24CC VPE02NOV24CC VPE03NCV24CC VPE03NOV24CC VPE04NCV24CC VPE04NOV24CC

File CAD su TraceParts
torna in cima
Flange fixing support for OCTOPUS systems without Vacuum generator

Flange fixing support for OCTOPUS systems without Vacuum generator

The fixing supports described on this page have been designed to connect an OCTOPUS system to a remotely installed vacuum generator or to an alternative vacuum source.
The supports, made with anodised aluminium, have two flanges: one to be fixed on the OCTOPUS system in the place of the generator and the other on the machine.
They are also equipped with connections for direct connection to the OCTOPUS system, to the generator or to the alternative vacuum source and to the instruments for reading and control of the level of vacuum. The unused connections can be closed with the metal caps provided.
The flange supports are currently available in the versions shown on this page and are suitable for OCTOPUS systems that use the vacuum generators indicated to beside the item:
- Art. SO 00 02 PVP 100 ÷ 200 M
- Art. SO 00 05 PVP 150 ÷ 300 MD
- Art. SO 00 06 PVP 450 MD
Note: The vacuum gauges and vacuum switches shown in the photo are not included with the supports.
Product codes: SO0002 SO0005 SO0006

File CAD su TraceParts
9.31  
torna in cima
Suction and blowing system AS

Suction and blowing system AS

With the suction and blowing system AS, we have tried to provide the printing industry with an answer to most of their requirements regarding the management of paper during the printing process, or rather:
- The concentration of all the necessary pumps and commands on one single piece.
- An increased printing quality thanks to individually controlled pumps.
- An increase of productivity resulting from the configuration and use of individual pumps.
- Reduced machine idle state due to the pneumatic pumps based on the Venturi principle.
- An improvement of the work environment thanks to the noise reduction, absence of heat and the emission of air free of oil vapours, water condensation and impurities between the sheets of paper to be separated and in the work environment.
- Energy saving due to a low compressed air consumption compared to the amount of sucked (or generated) air.
- Maintenance reduced to a regular cleaning of the filters.
The suction and blowing system AS is composed of a metal, easy-to-place cabinet, inside of which the combined pneumatic pumps PA and PS are located with the supply compressed air interception and adjustment valves.
The suction and blowing capacities of the pumps are determined according to the client’s requirements or to technical specifications of the machine manufacturer.
The blowing and suction connectors are located on the sides of the cabinet for the connection to the application, as well as the filters equipped with micro-porous cartridge against fine dust.
The following are installed on the control panel:
- The pneumatic main switch for supply compressed air interception with a pressure gauge for a direct reading of the line pressure.- The pneumatic switches for supply compressed air interception of every single pump.
- The pressure reducers with relative pressure gauges for adjusting the compressed air of every single pump. The vacuum (or pressure) level as well as the pump flow rate can be adjusted according to the supply air pressure.
- Vacuum gauges and pressure gauges for a direct reading of the vacuum and pressure at the application. - Vacuum gauges for controlling the clogging level of the PS pump filters.
All our pneumatic suction and blowing pumps can be combined regardless of their suction and blowing flow rate and can be installed inside the system cabinet. Given the enormous number of possible combinations, this catalogue only describes combinations of pumps with the same size.
Product code: AS4

File CAD su TraceParts
10.18  
torna in cima
Degasifiers

Degasifiers

The function of degasifiers is to suck the air bubbles that remain in the synthetic resin or composite material mixes and in silicone or similar compounds during their preparation. The presence of bubbles, in fact causes a drastic reduction of their technical features and negatively affects their appearance.
Degasifiers are composed of:
- One or two welded sheet steel autoclaves, featuring a perfect vacuum seal, equipped with transparent methacrylate lids that can be manually removed.
- An oil-bath rotating vane pump for high vacuum.
- One or two vacuum switches for a direct reading of the level of vacuum in the autoclave.
- One or two three-way manual valves for vacuum interception.
- A switchgear enclosed in a special protective casing.
- A profiled steel frame for assembling all the components.
Inside the autoclave, the degasifiers can reach a final level of vacuum equal to 99.5 %. With small modifications and with the aid of insulating or waterproofing resins these degasifiers can be used for vacuum-impregnating windings for electric motors, transformers, electric coils, etc.
Upon request they can also be supplied in different versions.
Product codes: DR10001 DR10002 D2R15001 D2R15002

File CAD su TraceParts
11.01  
torna in cima
Liquid-sucking pump sets

Liquid-sucking pump sets

These pump sets are for sucking liquids and collect them inside their tanks. The maximum level difference that can be exceeded is approximately 9 metres.
They are composed of:
- A welded sheet steel large-capacity tank- A compressed air-fed multi-stage vacuum generator
- A digital vacuum switch for adjusting the level of vacuum within which to operate
- A vacuum gauge for a direct reading of the level of vacuum in the tank
- A liquid level visible warning light
- Two magnetic switches for minimum and maximum liquid level
- One three-way vacuum solenoid valve for resetting the atmospheric pressure in the tank, with consequent automatic discharge of the accumulated liquid
- Two vacuum reducers for level of vacuum adjustment at the application
- Three manual valves for vacuum interception
- A switchgear enclosed in a special protective casing for manual or automatic operation selectionLiquid-sucking pump sets are normally used for extracting the water contained in washing machine and dishwasher filters that cannot be automatically drained after their commissioning.
They are also recommended for transferring dense liquids and creamy or muddy substances.
Available in other versions upon request.
Product codes: DVL150 DVL300 DVL500 DVL1000

File CAD su TraceParts
11.08  
torna in cima